Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
The article which follows pertaining to How to Install a Bathtub is indeed enjoyable. Read it for yourself and decide what you think about it.
Installing a bath tub isn't precisely rocket science, however it does require strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and place the new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's abilities, although you will require an assistant to leave the old bathtub and set in the brand-new one. See to it you have actually certified on your own for the job as well as fit trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Opportunities are you might need an expert plumber to make tube links.
This post will aid you install a brand-new bathtub in your shower room if you have currently bought a new tub as well as don't require to transform the arrangement of your previous water system pipes.
Your devices and also material checklist ought to comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, position the bathtub in the called for setting. The wooden boards are practical in equally spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system and also check all joints and also new pipework for leakages and tighten them if essential. Load the bathtub as well as also inspect the overflow electrical outlet and the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the supplier's user's manual. Tiling and also securing around the tub should wait up until the bathtub has actually been used at least once as this will certainly resolve it into its last setting.
Preparing for the Setup
First of all, the supporting framework supplied with the bath must be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to prevent pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, causing the water to pass through the wall between the bathroom and also the tiling, causing problems with dampness and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealant can split relatively very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly readily available on the marketplace. It is suggested to fit the tiles making use of water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that editorial about How to Install a Bathtub Yourself through someone on a different site. Enjoyed reading our blog posting? Please share it. Help others discover it. Many thanks for going through it.
Check It Out Report this page